Advertisement

Test Methodologies for Evaluating Broadband W-CDMA Receiver Designs

April 9, 2001 6:10 am | Product Releases | Comments

3GPP has defined a new suite of tests to evaluate W-CDMA. By Cliff Bailey, Spirent Communications Wireless broadband technologies continue to advance and mature at a remarkable rate. Wideband Code Division Multiple Access (W-CDMA) mobile radio networks promise higher data throughput, increased capacity, and seamless worldwide roaming on wireless networks....

LISTED UNDER: Services, Calibration / Test

LMDS Automatic Test System

April 6, 2001 6:38 am | Product Releases | Comments

The In-Phase Technologies' Model 1011 was developed to address the production test requirements of transceiver related components found in LDMS system designs. The use of ATE test methodology is mandatory in order to insure correlation of test results while achieving the stringent production throughput goals that exist in most LDMS component/system supplier organizations....

LISTED UNDER: Services, Calibration / Test

Single Board Computer for Development of Test Instruments

April 6, 2001 5:21 am | Product Releases | Comments

Tidal Engineering recently announced the addition of the SBC488A to its embedded IEEE 488 product family. This programmable single board computer (SBC) boasts a fully integrated C development environment and an IEEE 488 General Purpose Interface Bus (GPIB) controller to provide OEM's with flexible rapid instrument development capabilities withou the associated time and expense of developing a GPIB controller for their products....

LISTED UNDER: Services, Calibration / Test
Advertisement

Power Amplifier Test System

April 6, 2001 5:20 am | Product Releases | Comments

Anritsu Company, a provider in high-performance test and measurement solutions, has enhanced its ME7840A Power Amplifier Test System (PATS) with additional measurement capability, making it the most comprehensive solution for real-time simultaneous tuning of power amplifier parameters. The ME7840A can now conduct ACPR, IMD, PAE, compression, harmonics, and S-parameter measurements with a single connection, thereby creating a turnkey solutio...

LISTED UNDER: Services, Calibration / Test

RF Test Set for Bluetooth

April 6, 2001 5:20 am | Product Releases | Comments

Celerity Digital Broadband Test, a division of l-3 Communications, announced the introduction of the CS20310B Bluetooth® RF Test Set. This new test instrument records, analyzes and generates Bluetooth signals over full 83.5 MHz bandwidth, ensuring RF interoperability. It is also capable of digitally generating up to 12,800 hops at 1,600 hops/sec in the 2....

LISTED UNDER: Services, Calibration / Test

Passive Component Testers

March 2, 2001 7:56 am | Product Releases | Comments

QuadTech announced that its new family of LCR meters and impedance measuring instruments have been approved for CE marking, which is required on all products shipped into the European Union. The family presently consists of the Model 1910 Inductance Analyzer and 1920 Precision LCR Meter. The 1900 series is a new generation of high-performance testers specifically designed for fast throughput in automated production testing of resistive, cap...

LISTED UNDER: Passives, Capacitors | Services, Calibration / Test

Testmate Cable Assemblies

February 22, 2001 3:59 am | Product Releases | Comments

Times Microwave Systems has recently introduced its line of flexible 50 Ohm Testmate cable assemblies. Designed for operation up to 18 GHz or 40 GHz, Testmate cables have a proprietary triple shielding system and several designs feature interchangeable connector heads. Testmate cable assemblies have low attenuation, long term electrical stability and are ruggedized for daily dependability in a wide range of applications including site/field...

LISTED UNDER: Interconnect, Cables | Services, Calibration / Test

Slot Test Connector

February 21, 2001 9:09 am | Product Releases | Comments

Meritec's newest addition to the Test Connector family is the 242 position, 1 mm Slot Test Connector. It features a life cycle greater than 100,000, and was developed to eliminate many of the common problems associated with using a standard connector in a test application. When testing, the PCB is plugged in and out of the connector many times....

LISTED UNDER: Services, Calibration / Test
Advertisement

Pin Depth Test Gauge

February 21, 2001 8:22 am | Product Releases | Comments

Trompeter Electronics announced the addition of a new BNC Center Pin Depth Gauge, part number 010-0158, to their line of specialized Central Office installation tools. The new product is a precision dial gauge that meets the requirements set forth by the telecommunications industry for the proper installations of BNC connectors....

LISTED UNDER: Services, Calibration / Test

Testing Software

February 21, 2001 8:22 am | Product Releases | Comments

Anritsu introduces Cellular Repair Center Application (CRCA) software for use with its MT8802A Radio Communications Analyzer that creates a single test solution for fast, automated testing of TDMA, CDMA, GSM, and AMPS cellular phones. Anritsu has developed the CRCA software to simplify cell phone testing so technicians of any experience can conduct fast and accurate tests....

LISTED UNDER: Services, Calibration / Test

Bluetooth&#153 RF Test Set

February 13, 2001 9:49 am | Product Releases | Comments

Celerity Digital Broadband Test, a division of L-3 Communications, announced the introduction of the CS20310B Bluetooth™ RF Test Set. This new test instrument records, analyzes and generates Bluetooth signals over full 83.5 MHz bandwidth, ensuring RF interoperability. It is also capable of digitally generating up to 12,800 hops at 1,600 hops/sec in the 2....

LISTED UNDER: Services, Calibration / Test

RF Shielded Test Enclosures

February 13, 2001 9:48 am | Product Releases | Comments

The STE 5000 enclosure is an RF shielded enclosure design and value. The enclosure is roomy enough to hold even 19inches rack sized instruments, provides 𤩞 dB of shielding, and enables one to test anywhere in your facility. The box is constructed of type 304 stainless steel, and lined with microwave absorbent foam....

LISTED UNDER: Services, Calibration / Test

Testing Units

February 13, 2001 9:48 am | Product Releases | Comments

Schaffner EMC has introduced the ISN System 22, designed to help comply with new CISPR 22 standards. These standards require that all telecommunications ports on IT equipment be tested for RF emissions in the frequency rang eof 150 kHz to 30 MHz. Placed in a line, the ISN System 22 measures the emissions coming out of the device, and stabilizes the impedance at 50 ohms....

LISTED UNDER: Services, Calibration / Test

Test Set For Wireless Amplifier And Digital Radio Test

February 13, 2001 9:48 am | Product Releases | Comments

Celerity Digital Broadband Test, a division of L-3 Communications, announced the introduction of the CS2010W, a "virtual" test instrument for power amplifiers, software-defined digital radio, and digital signal encoder applications. The performance of this modular, single box system includes memory of 4000 MB and resolution via 14-bit D/As....

LISTED UNDER: Services, Calibration / Test

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading