By Andreas Roessler, Rohde & Schwarz
UMTS Long Term Evolution, short LTE, is the technology of choice for the majority of network operators worldwide, providing mobile broadband data and high-speed internet access to their subscriber base. Due to the high commitment LTE is understood as the innovation platform for the wireless industry for the next decade. That’s the reason why I link the abbreviation LTE more to the term LONG TERM EMPLOYMENT. The technology itself is high complex, utilizing advanced procedures on top of what we know from existing standards such as WCDMA or HSPA. This blog picks interesting aspects of LTE and takes a closer look while providing some explanations around it. A basic understanding of the concepts used for LTE and standardized by the 3rd Generation Partnership Project (3GPP) is assumed while reading.
You may ask why power allocation in the downlink is an aspect? It actually is ? and therefore I thought it is interesting to shed some light on it. Well, downlink power allocation can vary from cell to cell and furthermore it can be device specific. These settings – beside many others – will have an impact on the performance of an LTE-capable device. And data throughput is, of course, a performance criteria that not only network operators are judging, but also affect the user experience. But let’s start with the fundamentals first.
click to enlarge
Figure 1. Downlink power allocation in LTE.
As you know, cell-specific reference signals (RS) are embedded into the overall signal bandwidth at certain resource elements (RE). In the frequency domain every 6th subcarrier (= RE) carries a RS. The RS pattern is a pseudo-random sequence, whose generation depends on the cell’s identity and used cyclic prefix. Further a frequency shift is applied that is based on a modulo-6 operation. The mapping of the pattern is therefore cell-specific, but the scattering is always six subcarriers.
In the time domain every 4th OFDM symbol carries reference symbols. Due to their importance, reference signals are the highest powered components within the downlink signal. The power level for the reference signals is signaled within system information to the device, is cell-specific, and is in the range of -60 to +50 dBm per 15 kHz. It is a requirement that the LTE base station transmits all reference signals with constant power over the entire bandwidth. The power of all other signal components (synchronization signals, PBCH, PCFICH, PDCCH, PDSCH and PHICH) is set relative to this value. As mentioned above, there are OFDM symbols that do contain RE carrying reference symbols and there are OFDM symbols that do not. The relative PDSCH power for these symbols is given by two different parameters: p A and p B (see Figure 1).
click to enlarge
Figure 2. PB setting in a real LTE network captured with R&S®TSMW network scanner and R&S®ROMES drive test software.
PB is related to the cell-specific RS power and can not be changed dynamically. It can take one out of four integer values. Depending on the number of used transmit antennas (1, 2 or 4) each value corresponds to a certain ratio and thus power offset. The LTE networks that are currently deployed worldwide are supporting 2x2 MIMO. Let’s assume PB = 3. In that case the RE carrying data in that OFDM symbol where RS are present, are transmitted with an additional offset of 3 dB compared to symbols without RS [Ref.3]. For only one transmit antenna (SISO) PB = 3 translates to -3.98 dB. This is shown in Figure 1.
Now the question is, why all this is necessary?The overall goal is to have a constant power for all OFDM symbols to avoid power variations at the receiver (UE). With less PDSCH power given by PB the boost of reference signals is compensated, compared to OFDM symbols that do not contain reference signals. The PDSCH power depends always on the allocation, i.e. the number of allocated Resource Blocks (RB). Allocation can change from subframe to subframe, thus PA can also change on a 1 millisecond basis. While incorporating PA and PB it is ensured that the overall OFDM symbol power remains constant, even when the PDSCH allocation is changed.
What are values for PA and PB in a real LTE network?The later can be easily derived with Rohde&Schwarz drive test solution based on the TSMW network scanner and ROMES drive test software as it is a common network parameter. The integrated BCH demodulator decodes all system information, so PB and reference signal power can be easily found while decoding SIB Type 2 (see Figure 2).
Now what is the impact of PB, PA on device performance in terms of high data rates?
click to enlarge
Figure 3. Throughput Configuration Tool for LTE (TCT4LTE).
This type of testing helps design engineers to develop a good understanding on how the device performs at different network settings in terms of downlink power allocation to optimize the protocol stack, algorithms and hardware to deliver best results. Rohde & Schwarz helps to achieve these goals with its test solutions and tools.
References 3GPP TS 36.211 V8.9.0 Physical channels and modulation (Release 8), 2009-12
 3GPP TS 36.212 V8.8.0 Multiplexing and channel coding (Release 8), 2009-12
 3GPP TS 36.213 V8.8.0 Physical layer procedures (Release 8), 2009-09