Introduction to LTE Base Station RF Conformance Testing
Operator acceptance testing is yet another step in the process and includes more user-centric tests.
click to enlarge
Table 1. Base station RF transmitter characteristics tests.
The complex and flexible LTE air interface supports many options for modulation format (QPSK, 16QAM and 64QAM), frequency bands (FDD and TDD), resource allocations, and mobility. As a result, the number of RF configuration permutations that can be tested is enormous. In selecting the configurations for the LTE RF conformance tests, considerable effort was made by 3GPP to identify those combinations of parameters that represent the most difficult operating conditions so that when a product passes the tests, the design engineer can be reasonably confident that the device will perform satisfactorily in many more combinations than those explicitly tested.
Structure of the Base Station Conformance TestsThe base station RF conformance tests follows a standard format that includes the title; the definition of the parameter under consideration and applicability of the test to all or a subset of equipment; minimum conformance requirement with reference to the subclause of the 3GPP core specification that defines the minimum requirement; and the test purpose.
click to enlarge
Table 2. Base station RF receiver characteristics tests.
Base station conformance testing for LTE is similar to UMTS except for those areas of testing affected by the change to using an Orthogonal Frequency Division Multiple Access (OFDMA) modulation scheme. The base station RF conformance tests are defined in 3GPP Technical Specification 36.141  and are based on the core specification TS 36.104 . There are three main categories of conformance tests: transmitter characteristics, receiver characteristics and performance requirements.
Transmitter CharacteristicsTable 1 lists the transmitter characteristics test cases defined in the conformance test specification. These tests follow very closely the pattern from UMTS with differences mainly due to the use of OFDMA . The test for time alignment between the transmitter branches is particularly important to LTE because of the widespread use of transmit diversity, spatial multiplexing, and beamsteering. A time alignment of 65 ns is required, as is the case in UMTS, which specifies ¼ of a chip (65 ns).
The downlink reference signal power test (TS 36.141 subclause 6.5.4) is the equivalent of the primary Common Pilot Channel (CPICH) power accuracy test from UMTS.
click to enlarge
Table 3. Base station RF performance tests.
Performance RequirementsTable 3 lists the base station performance test cases currently defined in TS 36.141. Note that these represent only some of the requirements given in TS 36.104 subclause 8.
Downlink Test Models
click to enlarge
Table 4. E-UTRA Test Model mapping to test cases.
Three distinct classes of test models are defined: E-TM1, E-TM2, and E-TM3. The first and third classes have further subclasses. All test models share the following attributes:
• Defined for a single antenna port, single code word, single layer with no precoding
•Duration of one frame (10 ms)
• Normal cyclic prefix
•Localized virtual resource blocks, no intra-subframe hopping for PDSCH
•Cell-specific reference signals only; no use of UE-specific reference signals
click to enlarge
Table 5. FRC parameters for performance requirements (64QAM 5/6) from TS 36.141 Table A.5-1.
Each E-TM is defined for specific use according to Table 4.
An example of E-TM3.3 is shown in Figure 1. This signal was generated using the Agilent Signal Studio signal creation software and analyzed using the Agilent 89601A Vector Signal Analyzer software. Amplitude clipping was added to the signal to emphasize the impact this type of distortion has on EVM vs. time across the subframe. This can be seen in the top right trace.
Uplink Fixed Reference ChannelsThe LTE base station receiver and performance tests are carried out using uplink Fixed Reference Channels (FRCs) in a manner similar to UMTS. The base station FRC is similar in concept to the reference measurement channels used for UE testing. In most cases they are single-ended signals that can be generated in a signal generator without the need for any real time feedback.
The 64QAM example shown in Table 5 uses a code rate of 5/6, which is intended for testing the highest throughput requirements. For the 100 RB case of A5-7, there are 86,400 bits per 1 ms subframe indicating a maximum throughput of 86.4 Mbps. The base station performance requirements measured under fading conditions will be based on reaching a percentage of the maximum throughput under particular conditions. An example from TS 36.141 Table 188.8.131.52-6 demonstrates that a two channel eNB receiver operating in a pedestrian A channel with 5 Hz Doppler is required to reach 70% of the A5-7 FRC maximum throughput when the SNR is above 19.7 dB.
Conformance Testing Necessary but not SufficientFor any standards-based technology, the goal of conformance testing is to ensure that all devicesbase station and user equipmentmeet a minimum level of performance. Although the lists of conformance tests may seem large, other kinds of testing are still needed. For example, a more thorough investigation of performance margins is important since conformance testing gives a pass/fail result with no indication of how close the product is to a particular limit. LTE conformance tests are primarily designed to ensure that the network's underlying transport mechanisms are in place to carry end-user services, so at a higher level applications will need to be tested. Operator acceptance testing is yet another step in the process and includes more user-centric tests. Thus conformance testing is an important and essential step towards the successful deployment of a new system, but it is by no means the beginning or end of the test process.
Moray Rumney joined Hewlett-Packard/Agilent Technologies in 1984, after completing a BSc in Electronics from Edinburgh's Heriot-Watt University. He currently represents Agilent at RAN WG4, developing the air interface for HSPA+ and LTE. Moray has published many technical articles in the field of cellular communications and is a regular speaker and chairman at industry conferences. Hiroshi Yanagawa obtained his BSc in Communication Engineering from Shibaura Institute of Technology, Japan. He then joined Hewlett-Packard/Agilent Technologies and has worked in various engineering positions over the last 23 years. Hiroshi worked as a marketing engineer for impedance measuring instruments for five years and then moved to custom solution engineering. During this time he developed analog and digital cellular mobile and base station test systems as a system engineer. He is now designing an LTE design verification test system.
3GPP TS 36.141 V8.4.0 (2009-09) Base Station (BS) Conformance Testing
3GPP TS 36.104 8.7.0 (2009-09) Base Station (BS) Radio Transmission and Reception
3GPP TS 36.211 V8.7.0 (2009-05) Physical Channels and Modulation