High Speed Differential Interfaces and the Need for Common Mode Filtering and Protection
Wed, 09/29/2010 - 12:18pm
In the operating environment seen by electronics today there are numerous sources of electromagnetic interference (EMI) and radio frequency interference (RFI). This is due in large part to the increased use of RF technology. These types of interference result in the need for common mode filtering in applications utilizing differential interfaces. Although the desire in utilizing differential signaling is to minimize the effects of EMI/RFI, the effects are not eliminated entirely. The differential signal can become corrupted by external noise such that it is not discernable at the receiver. Also, with the noise having coupled into the electronics inside a device, other circuitry where differential signaling is not incorporated may be affected and cause addition problems.
click to enlarge
Figure 1. Typical High Speed USB 2.0 Eye Diagram.
USB 2.0: Common Mode Filter RequirementsIn a hi-speed USB 2.0 interface data is sent differentially over two wires at a speed of up to 480 Mbps. In order to understand the filtering requirements for such a signal, it is important to first understand the nature of the signal. The signal is a differential signal meaning that it is not referenced to ground, the two signals are referenced to each other. Data is transmitted over two lines with each line being exactly 180 degrees out of phase with the other. The two lines are commonly denoted as D+ and D- implying the phase nature of the signal. This means that an appropriate filter topology must be used to properly filter any unwanted content while not degrading the signal integrity of the desired differential signal.
click to enlarge
Figure 2. High Speed USB 2.0 Eye Diagram with Common Mode Noise.
click to enlarge
Figure 3. High Speed USB 2.0 Signal with Common Mode Noise Filtered.
Finally, the amount of attenuation necessary to sufficiently remove the effects of undesired common mode signals must to be determined. This is dependent upon the application, but in general the more attenuation the better.
USB 2.0: Signal Integrity Requirements
The signal shown in Figure 1 would be received with ease by a USB 2.0 transceiver since, as shown, the signal is without any eye diagram mask violations. Now consider a scenario where a common mode noise signal is introduced. For this example, a small amount of common mode noise with a frequency of 900 MHz and a peak amplitude of 75 mV is introduced. This frequency is chosen to emulate noise caused by the operation of a typical mobile phone. When the common mode noise signal is introduced, as Figure 2 illustrates, the eye diagram becomes quite degraded.
In Figure 2, the whole upper bound of the mask is being violated and signal transitions are becoming degraded and moving closer to violating the mask also. It would be virtually impossible for the receiver to interpret the data being transmitted in this case. There is too much noise present on the signal for the receiver to effectively differentiate between states under these conditions. This is with only a small amount of noise present with an amplitude of only five percent of the USB 2.0 signal amplitude.
USB 2.0: Protecting the InterfaceNot only is it important to filter EMI/RFI noise, but it is important to protect sensitive internal circuits from ESD events that can be harmful and even destructive. Under these conditions, a common mode filter with integrated low capacitance ESD protection such as the NUC2401 from ON Semiconductor is necessary. This filter provides the necessary bandwidth for the high speed USB 2.0 signal, proper common mode attenuation, and ESD protection for sensitive internal circuits. The integrated ESD protection has very low capacitance.
The resultant eye diagram in Figure 3 has no mask violations in either the upper or lower bounds or within the central region of the mask. This is with over five times the amplitude of noise introduced than in Figure 2. Even with such a high noise level, the resultant eye diagram at the output of the filter is discernable at the receiver and has maintained excellent signal integrity.
SummaryIn an environment rich in interference from numerous sources, filtering is incredibly important. A differential interface should help minimize some common mode noise effects; however, there are still issues with signal integrity as has been shown here. In addition, without proper filtering at the entry point to a device, such as the USB port, the noise can disrupt other internal circuitry. The ideal solution to remove this noise and absorb any ESD event at the entry point is to use a common mode filter with integrated ESD protection. Utilizing a common mode filter such as the NUC2401 enables the USB 2.0 interface to be much more robust in terms of immunity to EMI/RFI noise while also providing ESD protection. Even a small amount of EMI/RFI noise introduced to the high speed USB 2.0 signal can disrupt the signal and cause it to be indiscernible to the USB receiver.
Jonathan Harris is an applications engineer, standard products group at ON Semiconductor, www.onsemi.com