Transmitter RFIC Integration for Next Generation Wireless Infrastructure Radios
Mon, 02/08/2010 - 7:28am
Leveraging highly integrated RFIC designs and high dynamic range converters helps meet the challenges of next-generation base stations.By Phillip Halford and Ed Balboni, RF Group, Analog Devices, Inc.
click to enlarge
Figure 1. Simplified base station transmitter for 2G to LTE applications.
This provides increased challenges for the RFIC designer as integration needs to equal or better the performance of discrete implementation. With a discrete implementation, the system designer can pick and use devices optimized and designed for optimum performance using different technologies such as GaAs, Si Bipolar or CMOS. But this flexibility to select optimum process technology provides the greatest challenge for RFIC designer looking to offer higher levels of integration within a single process technology.
Within the base station transmitter, the analog I/Q modulator is the key RFIC component in determining the noise floor and linearity of the transmit signal path, so any relaxation in performance to reduce the size, power or cost is unacceptable.
click to enlarge
Figure 2. ADRF670X integrated LO phase noise vs. LO frequency.
Base Station LO DistributionOne of the important aspects of transmitter board level design is the local oscillator synthesis and distribution for the various up and down frequency conversion stages. The basestation LO distribution must retain phase coherence to all distant corners of the PCB and must also have low in-band and low wideband noise and low overall spurious content. The mixer performance is only be as good as the LO driving it, so a high quality LO is a critical element in the overall transmitter performance. In addition, very small amounts of phase noise, or spurious components on LO signals, can induce enough energy into analog signal paths to cause the transmitter to fail spurious emissions set by the major cellular communications standards (MC-GSM, WCDMA, LTE, WiMAX). The required LO for these standards ranges from about 500MHz to near 4GHz, which means that layout for the LO distribution must be handled with great care. The length of the traces from LO generation to its final termination should be kept as short as possible, but this is often difficult if the LO synthesizer must feed several different devices. One solution is to feed a common low frequency reference to a separate PLL synthesizers near each required LO, but this takes up significant real estate on the PCB.
The ADRF670x family of integrated modulators solves many of these problems, through the integration with a state of the art fractional-N PLL, and an integrated VCO. Using silicon germanium technology allows industry leading dynamic range in both the quadrature modulator and mixer with VCO to achieve performance that is competitive and significantly smaller than external VCO/PLL solutions. The VCO is implemented in upper level thick metal layers to build high Q on chip inductors as part of the LC tank. The VCO capacitor is formed using MOS switchable MIM capacitors allowing the VCO to switch frequencies over a wide frequency range with low phase noise. The band is automatically adjusted each time the PLL frequency is programmed thus providing a self-contained and reliable solution. The band size is chosen to ensure operation over the full temperature range once initially set. Thick metal is also used to integrate an output balun with excellent return loss for during subsequent stages. The ADRF670x family consists of 4 overlapping family members to cover frequency range and bands from 400MHz to 3GHz. Each family member is specified based on the output balun bandwidth over a 1dB and 3dB pass band.
click to enlarge
Figure 3. ACPR @ 2140 MHz for the ADRF6702.
Adjacent Channel Power Ratio MeasurementAdjacent Channel Power Ratio (ACPR) is a measurement which determines how much of a transmitted signal leaks into adjacent frequency bands. 3G standards such as WCDMA are very strict on the amount of power allowed to be transmitted out of band. The ACPR measurement for the ADRF6702 is shown in figure 3. The modulator provides highly linear output power and low noise enabling better than -76dB ACPR at -6dBm output. This helps reduce the number of gain stages following the modulator and maximize the dynamic range prior to the final power amplifier stages.
Figure 4. ADRF670X family of highly-integrated RF mixers and modulators.
In high density applications one ADL670X can synthesize an LO internally using its PLL, while other the other devices can disable their PLLs and use the common LO from the one master device.
The ADRF670X family as shown in figure 4 has been designed to minimize and ease the user interface to ADI's latest transmit digital to analog converter AD9122 and GaAs amplifiers such as the ADL5320 a ¼ watt high linearity amplifier capable of driving >0dBm into the final PA stage. This combination of devices completes the active IC content in three compact IC and is suitable for all cellular next generation multicarrier radio platforms.
ConclusionMulticarrier 3G and LTE 4G base stations will deliver a dramatic increase in data rates than what exists today. The migration to these next generation standards poses a number of challenges for base station manufacturers as they are under pressure to increase performance, capacity and density, while reducing the size of the base station and bill of materials cost. In order to address these challenges, increased pressure is then placed upon integrated circuit manufacturers, specifically within the radio signal path, to deliver very high performance components that are capable of addressing a wide dynamic range and that, without sacrificing performance, integrate multiple functions in order to reduce the footprint and thereby BOM costs. By leveraging highly integrated RFIC designs and high dynamic range converters, designers can effectively reduces the component count of next generation base stations by 60 percent.
By Phillip Halford is product marketing manager, RF Group, Analog Devices, Inc. He can be reached at email@example.com. Ed Balboni is a design engineer, RF Group, Analog Devices, Inc. Balboni can be reached at firstname.lastname@example.org.