The Role of Time-Domain in the Digital RF World
By Darren McCarthy
Many emerging applications call for a highly-capable RF analysis tool that captures
the dimension of time along with the traditional frequency and amplitude axes.
Many of today’s RF signals change from one instant to the next. Some hop frequencies,
others spike briefly, and then disappear. Many can have complex modulation that
can dynamically change in an instant. And these activities can produce their own
side effects: random transients, interference, switching anomalies, and more.
What do all these phenomena have in common? Time. Time is the axis that can no
longer be ignored.
In this article, the basic measurement tasks required of RF tools are explored
in order to establish the critical nature of time in digital RF. This leads to
a review and comparison of approaches to signal discovery, triggering, capture
and analysis.
RF Transmission classes
The digital RF revolution has introduced an unprecedented number of useful devices
while lowering their cost and power consumption. Whole communications systems
are
click to enlarge
Figure 1. The swept spectrum analyzer steps across a series of frequency segments,
often missing important transient events that occur outside the current sweep
band. |
integrated in monolithic silicon. The proliferation of information being transmitted
over an increasingly scarce spectrum has driven a need for ever higher data rates
per unit bandwidth and for complex communications protocols that allow the peaceful
co-existence between RF devices and systems. A key goal of communications protocols
is to reliably transmit a packet of data in as little bandwidth as possible over
as short a time as possible while minimizing interference. While not designed
for communications, radar systems have similar objectives of spectral efficiency
and minimum interference with the added goals of security and detection avoidance.
This has led to several classes of RF transmissions, including:
•Transmissions that turn on only for the brief time it takes to transmit a unit of data, releasing the spectrum for other use as soon as the data is sent. In many cases the timing of these short transmissions is unknown and random.
•Systems that share the same spectrum at the same time as in ultra-wide-band
(UWB) and code division multiple access (CDMA). •Cognitive radios (CR) adjust
frequency, modulation and power in response to the spectrum environment at a particular
point in time and location and can build upon prior knowledge. •Shared package:
Multiple RF devices inside a single package. •Shared silicon: RF devices sharing
the same silicon as digital CPUs with clock rates in the GHz range.
RF Measurement Challenges
Now let’s consider some of the basic measurement tasks required of today's RF
tools in order to allow designers to achieve their goals. In one form or another,
these tasks are common in the various classes of RF transmissions and span applications
ranging from surveillance to physics research.
•Characterizing frequency drift— Frequency settling time
and response often must be characterized to ensure that a device meets functional
and operational needs. This requires uninterrupted capture of a signal whose frequency
is constantly changing over time . •Detecting
interference signals and their sources— Interference signals come
and go, often as a result of switching activities inside or outside the system
from intentional or unintentional sources. By recording many discrete instances
of interference plus the surrounding time, it is possible to localize the offending
frequency and infer its source. •Finding and analyzing transient signals—
Transient frequency changes, whether glitches or intentional transmissions, can
appear unexpectedly amid steadier and even higher level signals. Detection requires
some means of distinguishing events of interest from everything else that is going
on the observed span. •Capturing and analyzing channelized signals beyond
baseband— Baseband signals are often upconverted to a specific channelized
band of operation called a passband. Passband signals can be agile and modulated,
making it necessary to capture everything that occurs in the frequency band of
interest over a period of time. An uninterrupted spectral record is required so
the spectrum, time, and modulation characteristics of the signal can be explored.
•Analyzing adaptive digital modulation— Adaptive digital
modulation is growing increasingly common and complex as bandwidth becomes more
precious and security more important. Analyzing modulation quality and its relationship
to the signal's frequency and time-domain characteristics is a key step in wireless
troubleshooting during transitions. Often, testing is required to go beyond standards,
especially as implementation is not defined. In reviewing this list of RF measurement
tasks, it is clear that many emerging applications call for a highly capable RF
analysis solution: a tool that captures the dimension of time along with the traditional
frequency and amplitude axes.
Currently there are three types of RF Signal Analyzers available: the swept Spectrum
Analyzer (SA), the Vector Signal Analyzer (VSA), and the Real-Time Spectrum Analyzer
(RTSA). Below we take a closer look at each its ability to meet emerging digital
RF design requirements.
Swept Spectrum Analyzers
The traditional swept spectrum analyzer makes amplitude vs. frequency measurements
by sweeping a resolution bandwidth (RBW) filter over the frequencies of interest.
The disadvantage is that it only records the amplitude data in one frequency at
a time. A relatively stable, unchanging input signal is required. Figure 1, the
sweep is looking at frequency segment at time Ta while a momentary aberration
is occurring at a higher frequency. By the time the sweep arrives at the higher
frequency segment, at time Tb, the aberration has vanished. It does not get detected.
There is no way to trigger on defined signal characteristics, nor is there a way
to accumulate a record of longer-term signal behavior.
Vector Signal Analyzers
The vector signal analyzer emerged to address the distinctive requirements of
digitally modulated signals.
Unlike the swept SA, the VSA is optimized for modulation measurements. It captures
the whole signal and any digital modulation effects occurring at one instant in
time and stores a record into memory. This process is also a limitation as the
capture cannot be triggered by a frequency defined event.
RF Real-Time Spectrum Analyzers
As time-varying signals become more common in RF applications, the need for an
alternative approach to RF acquisition and analysis becomes more urgent. The Real-Time
Spectrum Analyzer has emerged to solve this tough measurement problem. Alone among
the three spectrum analyzer architectures, the RTSA can trigger on a frequency
domain event, then capture and analyze any passband signal that falls within its
real-time bandwidth.
Figure 2 depicts the RTSA architecture. An integrated down-converter positions
the real-time bandwidth on any passband up to the analyzer's upper limit. After
filtering, the down-converted signal goes through an ADC that digitizes it. This
allows real-time triggering of frequency domain events, capturing of the signals
into memory, and multi-domain analysis of the time, frequency, and modulation-domains.
The RTSA's digital IF architecture allows a continuous capture of a signal over
time. Once triggered on a frequency defined event, the signal is then stored in
the memory as a seamless, continuous record of time.
The RTSA is the only RF signal analyzer that is optimized to produce a three-dimensional
display: frequency, power (amplitude), and time.
Shedding Light on Problems
Recognizing that a problem exists is the first step to resolving it. Problems
specific to digital RF are often discovered indirectly. Transients in one device
may cause increased
click to enlarge
Figure 2. Real-Time Spectrum Analyzer architecture. The instrument
captures a full passband of frequencies all at once and the DSP supports flexible
trigger and analysis features. |
bit error rates in another. Radars may occasionally provide inaccurate target
information due to self-jamming or susceptance to transient interference. Thermal
or electrical memory effects in a power amplifier may cause lost data and momentary
interference with adjacent channels. The execution of a computationally intensive
software subroutine may cause power supply voltage variations that affect the
quality of RF transmissions.
To enable RF designers to discover problems, Tektronix has developed digital phosphor
or DPX™ technology to emulate variable persistence CRTs. The implementation
of digital phosphor spectrum analysis used in Tektronix Real-Time Spectrum Analyzers
combines display processing with dedicated DSP hardware that perform frequency
transforms several orders of magnitude faster than traditional spectrum analyzers.
At almost 50,000 trace updates per second, the DPX technology has about 100,000%
more spectrum updates than a traditional swept spectrum analyzer.
The information from each transform is combined in the DPX engine generating displays
at a full motion rate. This engine includes statistical persistence processing
that allows full-motion viewing of signal behavior over time. It also makes weak
signals interspersed amid strong ones instantly visible and highlights infrequent
short-duration events. Persistence adjustments allow the user to optimize display
characteristics for varying signal conditions, from a live RF view of dynamic
signals to the discovery of single occurrences. This sheds light on signal behavior
that was not viewable with traditional spectrum analyzers or vector signal analyzers.
Other Real-Time Spectrum Analyzer features provide means to trigger on signal
behavior, capture those signals in memory and analyze them in the time, frequency
and modulation domains
Summary
As RF signals become more complex and less predictable, designers need to understand
time-varying signal behavior ranging from frequency hopping to EMI transients.
While a number of instruments are available for RF measurements, only the RTSA
offers the triggering, capture and analysis features needed to all designers to
go forward with emerging trends in RF design.
About the Author
Darren McCarthy is the market development manager for RF Test, Tektronix, Inc.
Tektronix, Inc.
14200 S.W. Karl Braun Dr., PO Box 500
Beaverton, OR, 97077
© 2008 Advantage Business Media
|
