Advertisement
The Source on Design and Technology for the Wireless and RF Engineer
Subscribe to Wireless Design and Development All
View Sample

FREE WDD Email Newsletter

Board-on-Chip

May 30, 2003 11:46 am | Product Releases | Comments

Altium announces a technology that enables engineers to us board-level design methodologies to both design and implement a digital system, including embedded microprocessor cores and the software that runs on them, onto an FPGA. The board-on-chip system includes mixed schematic/VHDL design capture; integrated software development; processor core packs that combine pre-synthesized processor cores with matching compiler, simulator and debugge...

Controller ICs

May 30, 2003 11:46 am | Product Releases | Comments

Designed to provide a compact and efficient solution, the half-bridge (Si9122, Si9123) and push/pull (Si9124) devices operate over a 12- to 72- input voltage range, drive both primary-side MOSFETs, and provide timing for the secondary synchronous rectifiers. Each device incorporates a secondary-side FET drive signal for synchronous rectification and a direct primary MOS drive (1-A maximum) on the high and low side....

Ceramic Material

May 30, 2003 11:46 am | Product Releases | Comments

The E7000 is a high Q material that achieves low losses at 8 - 15 GHz. High frequency applications such as 3G base station filters, ultra-stable oscillators and high performance radio links can benefit from this material's Q.F of 200,000 to 250,000 at 10 GHz according to temperature coefficient....

Advertisement

Multi-channel Transceiver

May 30, 2003 11:46 am | Product Releases | Comments

ASTRX1 is a low cost, System-on-Chip (SoC), multi-channel transceiver. Offering two-way communications at burst data rates of up to 40 kbps over short ranges, the ASTRX1 transceiver is suited for wireless data applications. The multi-channel transceiver features frequency range options of 868 - 870 and 902 - 928 MHz....

High Power Limiter

May 30, 2003 11:46 am | Product Releases | Comments

The PMI Model No. LM-20M80M-10-20W high power limiter operates from 25 to 80 MHz (other frequencies are available), with an input power level of 20 watts. Insertion loss is 0.5 dB maximum. VSWR is 1.5:1 typical. There is a 1 μsec recovery time. The output limiting is +15 dBm maximum. The size is 1....

Power Supply Controller

May 30, 2003 11:46 am | Product Releases | Comments

The LTC2920 adjusts the power supply voltage by sourcing or sinking current into the feedback node of the controller chip or the voltage adjust pin of the regulator module. The margining current is set with a single resistor channel. The output current is settable over a 400:1 range and the margin voltage precision of < 0....

Switching Platform

May 30, 2003 11:46 am | Product Releases | Comments

Model 1260-64M is a four position, modular, microwave switching platform. The 1260-64M, VXI module, accepts up to 4 microwave switch plug-ins in a dual-slot module. Different types of microwave relays, from DC to 40 GHz, are available and can be accommodated on this switch card. User connections are made directly to the relay via front panel connectors....

Mobile Test Platform

May 30, 2003 11:46 am | Product Releases | Comments

The Seven.Five multigeneration wireless test family is a mobile test platform that is adaptable to any test application. It provides wireless infrastructure analysis, benchmarking, and optimization for 2G, 2.5G, and 3G network deployments. The family consists of Seven.Five Solo, Seven.Five Duo, Seven....

Advertisement

Programmable Synthesizer PLLs

May 30, 2003 11:46 am | Product Releases | Comments

Temex introduces programmable synthesizer PLLs to reduce BOM costs for high performance microwave communication products from 100 MHz to 2.5 GHz. The first three devices of this new range are the 1050 - 1090 MHz PLC1050, the 1550 - 1620 MHz PLC1550, and the 2105 - 2175 MHz PLC2105. The PLC series PLLs display low SSB phase noise, typically around 90 dBc/Hz at 100 kHz, as well as fast switching speed....

AC Switches

May 30, 2003 11:46 am | Product Releases | Comments

The ACS family of switches is designed to control small pumps, fans, valves, relays, dispensers, door locks and micro-motors. The switches have high gate sensitivity, enabling them to be directly driven by microcontrollers and ensuring low power consumption. The high blocking voltage (up to 500 V) and clamping voltage (up to 1100 V) of the ACS devices means they can withstand the back-EMF created by inductive loads running from 240 V mains ...

Impedance Matching Pads

May 30, 2003 11:46 am | Product Releases | Comments

Models 854-012-IMP and 874-013-IMP match 50 Ohms to 75 Ohms and 75 Ohms to 50 Ohms resepectively. Both modules feature a DC - 2000 MHz frequency range and BNC connectors (male/female). These devices are a low cost solution to matching the impedance of a circuit or device under test to 50 Ohm test equipment....

Type N Attenuator

May 30, 2003 11:46 am | Product Releases | Comments

Model 352-019-XXX is a precision 2 watt fixed attenuator that has a frequency range of DC - 18 GHz with attenuation values of 1 to 30 dB available. These units feature a VSWR of 1.35:1 maximum in a 1.76 inch long passivated stainless steel enclosure with Type N male/female connectors. www.broadwavetech....

Automatic Bonders

May 30, 2003 11:46 am | Product Releases | Comments

Model 5060 Automatic Ball Bonder and Model 5070 Automatic Wedge Bonder offer large area, deep access, ball and wedge wire bonding for microelectronic packaging applications. They have a large 12 inches× 5 inches work area and are designed for ergonomic operation. The 5060 provides thermosonic ball and stitch bonding with a heated workstage and an optional capillary heater....

Circuit Protection Modules

May 30, 2003 11:46 am | Product Releases | Comments

Bel introduces SIP circuit protection modules. These integrated devices combine fuses, overvoltage protectors and resistor networks into a vertical mount, SIP configuration to conserve PCB real estate, optimize manufacturing throughput, and accelerate time-to-market. The modules feature Bel's 1....

Dual EMI Air Filters

May 30, 2003 11:46 am | Product Releases | Comments

Broadband dual EMI air filters from Universal Air Filter integrate technology that meets the EMI/RFI noise shielding requirements of broadband communications equipment utilizing forced air cooling techniques. The Broadband air filter integrates the honeycomb and/or stainless steel mesh EMI shield into the air filter assembly....

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading