Advertisement
The Source on Design and Technology for the Wireless and RF Engineer
Subscribe to Wireless Design and Development All
View Sample

FREE WDD Email Newsletter

Parabolic Dish Antenna

July 2, 2003 9:56 am | Product Releases | Comments

Pacific Wireless announces a parabolic dish antenna designed for use in high-performance communications and data link applications operating in the 5 GHz frequency range. The antenna is available in two frequency options suitable for transmit and receive functions in the 5.8 GHz ISM band and the 5....

Horn Antennas

July 2, 2003 9:56 am | Product Releases | Comments

Schaffner EMC introduces a double-ridged guide horn antenna that offers a frequency range of 1 - 18 GHz. The BHA 9118 is a linearly polarized, broadband antenna used for both receiving and transmitting in chambers or open area test sites. The antenna has a field strength capability of 250 V/m at 1 m, and a high typical gain of 5....

Patch Antennas

July 2, 2003 9:56 am | Product Releases | Comments

Nearson patch antennas operate in the 2.4 GHz or 5.x GHz band for 802.11(b), (g) and (a) applications. The patch antennas are designed in a small compact housing which provides high efficiency and a low cost solution. These antennas are a single array, linear polarization with a 60( beam width available in two models, SPA-003 and SPA-010....

Advertisement

Single Antenna System

July 2, 2003 9:56 am | Product Releases | Comments

Decibel Products'new antenna system, 931DG70VTREM, contains three independent ± 45° antennas under a single 6 inches radome. The 931DG70VTREM allows for independent beam tilting to optimize each sector....

Dual Polarized Antennas

July 2, 2003 9:56 am | Product Releases | Comments

LGP Allgon introduces a line of broadband, dual polarized antenna products that offer expanded spectrum and increased flexibility to help networks evolve with technology and user demand. Their space-efficient design is well suited for rural and metropolitan locations with strict zoning requirements....

Dielectric Chip Antenna

July 2, 2003 9:56 am | Product Releases | Comments

NTK Technologies announces a series of SMD ceramic dielectric chip antennas designed for WLAN applications. The MAC2450A5362AAE series measures 11.8 × x 2.5 × 0.7 mm. These dual band antennas are available with a center frequency of 2450 GHz and 5362 GHz. They deliver a wide bandwidth (VSWR=2) covering 2400 - 2500 GHz and 4900 - 5825 GHz respectively....

Millimeter Wave ICs

July 2, 2003 9:47 am | Product Releases | Comments

M/A-COM introduces three millimeter wave power amplifiers for radar, satellite and point-to-point communications. The products offer Ka-band operation from 31.5 to 36.0 GHz range and Ku-band operation from 15.5 to 18.0 GHz. The MAAPGM0046-DIE, MAAPGM0012-DIE, and MAAPGM0013-DIE are 3-stage power amplifiers matched to 50 ohms on both the input and output ports....

Field Effect Transistors

July 2, 2003 9:47 am | Product Releases | Comments

Toshiba announces a 90-watt C-Band GaAs field effect transistor (FET). The TIM5964-90SL features output power of 49.5 dBm (typical) at a frequency range of 5.9 to 6.4 GHz. Gain (G1dB) is 7 dB typical. Drain current (IDS) is 18.0 A typical. IM3 is – 40 dBc typical at 43.5 dBm S.C.L. (949) 455-2000; www....

Advertisement

RF Receiver ICs

July 2, 2003 9:47 am | Product Releases | Comments

The UPB1008K is a single-chip double-conversion RF-to-IF I-Q frequency translator designed to provide a complete RF front end for GPS systems. It combines a low noise amplifier, VCO, PLL, IF AGC amplifiers, I-Q demodulators, I-Q IF amplifiers, and 2-bit A/D converters in a single, compact 36 pin QFN package....

Wideband VCO

July 2, 2003 9:47 am | Product Releases | Comments

The MW0500-1423 VCO covers 2.5 - 5.0 GHz while providing +4 dB output and ± 1dB flatness, over a tuning voltage range of 0 to 22 V. In a low cost compact 0.500 inches sq. x 0.15 inches SM package, the MW500-1423 draws 30 mA from a +5 V supply. Phase noise is typically – 105 dBc/Hz @ 100kHz, and harmonics are at least 20 dB down....

Noise Calibration Standards

July 2, 2003 9:47 am | Product Releases | Comments

Noise Com announces the NBS-Series of broadband Noise Calibration Standards for calibration laboratories, radiometer test and verification, and low noise amplifier tests. Using a low-loss waveguide horn design, Noise Com isolates the cold parts from the waveguide, which is controlled at ambient temperature, and avoids condensation of humidity and errors from temperature gradients....

Dual Channel Battery/Charger Simulator

July 2, 2003 9:47 am | Product Releases | Comments

Keithley introduces its Model 2306-VS dual channel fast transient power supply with external triggering. Designed to meet the evolving test needs of handset and cellular component manufacturers, the Model 2306-VS allows externally triggered output voltage level changes with additional measurement capability....

TOPICS:

Low-Cost Transceivers

July 2, 2003 9:47 am | Product Releases | Comments

Smaller than a credit card, the cost efficient 9XCite™ 900 MHz Wireless Transceiver Module provides FCC-approved, Frequency Hopping Spread Spectrum, TTL (or RS-232/422/485) communication an extremely low price. The 9XCite requires no set-up, operates from 2.85 - 5.50 V DC, provides long range with receiver sensitivity of – 108 dBm, extends battery life using power-down mode of 18 μA, and delivers data throughput rates of 9600 bp...

Semiconductor Packaging

July 2, 2003 9:47 am | Product Releases | Comments

StratEdge announces a discrete semiconductor package product family. The packages are available with lead profiles meeting JEDEC standards. They are assembled using a glass to metal seal process. The hermetic seal provides reliability for the device, and offers protection from environmental conditions....

Step Attenuators

July 2, 2003 9:47 am | Product Releases | Comments

Alan Industries introduces the PDS series of Step Attenuators. These step attenuators operate over the DC - 2200 MHz frequency range, with up to 69 dB of total attenuation available. Each unit is supplied with index stops; knobs, and provisions to panel mount the device. Bench top brackets are also available as a mounting option for laboratory attenuator applications....

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading