Improving Power Amplifier Efficiency in CDMA and WiMAX Systems
Efficient design and implementation of crest factor reduction and PA linearization solutions.
By Clinton Chan, TelASIC Custom Solutions & Deepak Boppana, Altera
WiMAX is an acronym for Worldwide Interoperability for Microwave Access, a certification
mark for products that pass conformity and interoperability tests for the IEEE
802.16 standards. The WiMAX Forum, formed in 2001, describes WiMAX as “a
standards-based technology enabling the delivery of last mile wireless broadband
access as an alternative to cable and DSL”.
The orthogonal frequency division multiplexing (OFDM)-based WiMAX 802.16e standard
is expected to offer higher data rates compared to the current 3G technologies.
click to enlarge
Top, Figure 1. Third-generation CDMA base
stations transmit a composite downlink signal formed by summing up different physical
channels. |
To achieve this goal, the transmitter chain must transmit with high fidelity and
power to cover a large area utilizing only a few cell sites. This puts high demand
on power amplifier (PA) performance. However, the nature of code-division multiple-access
(CDMA) and OFDM signals makes it difficult to achieve high PA efficiency.
As an example, base stations in third generation (3G) CDMA-based systems transmit
a composite downlink signal (see Figure 1). This downlink signal is formed by
summing up different physical channels. These different physical channels include
dedicated data and control channels for different users apart from the always
required common control channels.
As the number of users in the system increases, the time-varying composite signal
envelope exhibits a high peak-to-average ratio (PAR) or crest factor. Crest factors
of the downlink signals are as high as 15 dB for single carrier systems and 20
dB for base stations with multiple CDMA carriers. Similarly, as the number of
sub-carriers increases, the PAR of the OFDM signal also increases. Signals with
high crest factors degrade the efficiency of the power amplifiers that amplify
the downlink signals in base station transmitters.
click to enlarge
Figure 2. An efficient CFR technique involves the peak windowing algorithm,
which requires a FIR filter for implementation. |
The operating point of the PA is reduced or backed off in order to accommodate
input signal peaks and to keep waveform distortion within specified limits. Back
off is done to maintain linearity at the PA output and prevent out-of-band radiation.
Input signals with a high crest factor need large back-off and will lower the
efficiency of the PA. Consequently, designers face the challenge of reducing the
crest factor of the input signal and preventing the efficiency of the PA from
falling to unacceptable levels.
Crest Factor Reduction
Clipping signal peaks is the simplest way of reducing the crest factor. However,
hard clipping causes sharp corners in the clipped signal, degrading signal quality
and increasing the out-of-band radiation. Peak windowing is a technique that
smoothes the sharp corners by multiplying the signal to be clipped with a windowing
function and is especially useful for CDMA systems.
The magnitude of the original signal x(n) is compared with a threshold
value A to yield an intermediate scaling factor c(n). This is then
convolved with the window coefficients w(n) to generate the final
windowed scaling factor b(n) as shown below:
A windowing finite impulse response (FIR) filter with a feedback structure can
be used to calculate the clipping function b(n). The feedback structure
is used to calculate a correction term using the previous input values to prevent
over clipping of consecutive samples. Choosing the length of the window L involves
a trade-off between the signal quality and the out-of-band radiation. This choice
must be selected appropriately to satisfy base station radio transmission requirements.
Another CFR technique involves selecting and ordering signals for transmission.
The result is a low crest factor. This involves complicated calculations and highly
complex hardware at the digital modulation stage. But it can reduce the signal
crest factor without distortion because the CFR system monitors the signal and
re-orders the transmission for a low crest factor.
Once the crest factor is reduced, designers are confronted with a signal distortion
issue. When signal peaks are smaller, the signal is distorted, which leads to
possible violation of the stringent WiMAX -31 db error vector magnitude (EVM)
specification. Digital pre-distortion (DPD) remedies this problem. DPD calculates
the distortion caused by the PA, defines it, and applies pre-distortion to the
input signal. When the signal exits the PA, it is pre-distorted.
Relying on Analog Feed Forward
Designers have generally relied on analog feed-forward (AFF) systems to deal with
signal distortion. AFF presents additional design issues. Designers work with
analog components requiring fine tuning. Additionally, these components dissipate
considerable heat, consume inordinate space and lack the integration possibilities
of digital circuits.
AFF is vastly different than DPD. With AFF, a final corrected signal output
is generated by finding the difference between the undistorted original input
signal and the distorted PA output signal. Therefore, this approach is post-correction,
thus the name, feed forward.
Feed forward generates a correction signal, which is applied to the output. The
correction signal is derived on-the-fly by subtracting a sample output of the
PA from an undistorted
click to enlarge
Figure 3. This solution for an adaptive DPD uses the blind adaptive LUT-based approach. |
input sample and amplifying the result in an error amplifier. This system requires
no knowledge of the signal and can accept a modulated RF carrier as the only input.
DPD requires the insertion of a non-linear module before the RF power amplifier.
This non-linear module, called the pre-distorter, has the inverse response of
the PA so that the overall response at the output of the PA is linear. Adaptive
DPD involves the digital implementation of the pre-distorter and the presence
of a feedback loop that adapts to the changes in the PA response due to varying
operating conditions.
Efficient CFR and DPD Hardware Design
Altera provides FPGA-based and DPD reference designs for CDMA systems. The first
CFR technique noted earlier requires a FIR filter to implement the peak windowing
algorithm. DSP blocks embedded in the FPGA efficiently implement this peak windowing
algorithm. Each DSP block operates at over 370 MHz and has a number of multipliers,
followed by adder/subtractor/accumulators in addition to registers for pipelining.
The FIR compiler MegaCore is used to calculate window filter coefficients. It
also automatically generates code required for the software to synergize high-speed,
area-efficient FIR filters of various architectures.
The instantaneous amplitude of the complex symbols are efficiently calculated
with a coordinate rotation digital computer (CORDIC) solution. CORDIC is an iterative
algorithm that performs various trigonometric functions by using only additions,
subtractions and shift operations. CORDIC uses logic elements (LEs) operating
in arithmetic mode. Each LE is configured to contain a full adder/subtractor cell
plus an associated register. The deeply pipelined, parallel architecture enables
operation speeds over 300 MHz.
Figure 3 shows Altera’s solution for an adaptive DPD using the blind adaptive
LUT-based approach. Incoming samples (I and Q) have correction factors applied
from the LUT and sent to the radio frequency (RF) module. The address of the LUT
is derived from the input power, and the LUT contains two values for each location,
the real part, I, and the imaginary part, Q. In the feedback loop, the output
of the PA is downconverted — transformed to polar form — and compared
with the delayed version of the input to the pre-distorter in polar form. This
error is then used to update the values currently stored in the LUT.
Embedded DSP blocks, RAM and soft core processors play major roles in this effective
DPD design. Applying correction factors from the LUT involves complex multiplications
that map well into the embedded DSP blocks of the FPGA. Embedded RAM includes
512 bit, 4 kbit, and 512 kbit blocks. The 4 kbit and 512 kbit blocks can be used
for LUT implementation, while 512 bit blocks, in shift register mode, are ideal
for delaying input samples for error calculation. Thirdly, embedded processors
allow designers to quickly modify the DPD adaptive algorithm in software and customize
their solution without scheduling complex data paths. This integration of the
forward and feedback paths within the FPGA eliminates the need for external DSPs
and reduces system costs and board size.
Turn-key WiMAX Radio Head
TelASIC Communications offers a turn-key radio head for WiMAX base stations. The
solution consists of a chassis containing the receiver, transmitter with PA linearization,
power
click to enlarge
Figure 4. A single FPGA can be used to implement both the proprietary designs of dynamic CFR (DCFR) and dynamic DPD (DDPD). |
amplifier, operation and maintenance controller, and CPRI-based digital interface
to the baseband. TelASIC worked closely with Altera and used its FPGAs. Figure
4 shows a diagram of TelASIC’s WiMAX radio head. It achieves 25 dB linearization
correction with 30% power amplifier efficiency and has the ability to support
20 MHz of instantaneous signal bandwidth.
A single FPGA implements TelASIC’s WiMAX-specific dynamic CFR (DCFR) and
dynamic DPD (DDPD) that linearizes a power amplifier with high efficiency, even
at the EVM of 2.5% to transmit up to 40W from a power amplifier using standard
off-the-shelf LDMOS transistors. The radio can be configured for one or two carriers
(10 MHz each). FPGAs with embedded digital signal processing (DSP) blocks and
soft processors provide TelASIC designers with a perfect platform for implementing
CFR and pre-distortion solutions. Altera’s Nios II embedded processors operate
at over 150 MHz and can use custom instructions for hardware acceleration of program
code.
TelASIC’s linearization technique is “dynamic” because of the
high speed of operation and is desirable for quickly tracking changing operating
conditions in the power amplifier.
FPGAs were used to develop the DCFR and DDPD designs to reduce the cost of multiple
design iterations that, otherwise, would have been incurred in ASIC development.
These designs were subsequently migrated from FPGA to Altera’s HardCopy
structured ASICs as product volumes increased. These structured ASIC-based designs
are shipping in volume to lower production costs to ASIC-type levels and to reduce
power consumption.
About the Author
Clinton Chan is manager customer solutions for TelASIC, El Segundo, CA and
Deepak Boppana, Sr. is technical marketing engineer for Altera, San Jose, CA.
Altera Corporation
http://www.altera.com
©
2008
Advantage Business Media
|
